OEM CONVERTER – VMA420-4AXIL - Quad In-Line voltage (XV) to current (C) converter (transducer) transmitter & splitter.

This board offers effective, state-of-the-art, reliable linear control of HVAC's 4-20mA dampers and valves. Commonly utilized as the heart of 420 In-Line Amplifier 420ILA.

The CONVERTER-VMA420-4AXIL Quad voltage to current converter is a signal control (Proportional) 0-20mA or 4-20 mA voltage to current transducer board for HVAC (Heating, Ventilation and Air Conditioning), electro-hydraulic and servo electronics; actuator, dampers, bleed pilot valve, globe valves, butterfly valves, plug valves, dampers and more.

The CONVERTER-VMA420-4AXIL board is designed to perform Quad voltage to current conversion and or splitter (transducer). If used properly, it will eliminate the need for an expensive board, which would otherwise be needed to carry out the same tasks.

Shown above, Model 4ILAX, 4 channel in-line voltage (0/2-10VDC signal) to 4 current outputs (0/4-20mA) converter/splitter board, with 18 terminal block, power of 24V or 28V AC or DC

QUAD Voltage to 0-20mA Outputs, Splitter, Re-transmitter, Duplicator In-line Transducer

The CONVERTER-VMA420-4AXIL Quad Voltage input signals i.e 0-10V. 2-10V, 4.8b-24V... to Quad Outputs 0-20mA or 4-20 mA Splitter / converter/ Re-transmitter. Simple linear 4-way signal duplicator for remote applications up to few mils.

The CONVERTER-VMA420-4AXIL  is easy to install, setup, and operate. If you want to do professional remote voltage measurement related functions, The CONVERTER-VMA420-2X offers the features you need. It can be mounted easily via four 0.125" mounting holes using 4-40 screws.

Simply connect the board to 24VDC or 24VAC connect your Quad voltages source 0-10V to the inputs and our board will convert it to Quad 0-20mA. Where; for input voltage 2-10V the outputs current is 4-20mA.

The CONVERTER – VMA420-4AXIL transducer board is an accurate, linear, and an efficient way to convert industrial standards Quad voltage (input DC voltage models) 0 to 10V, 2 to 10V, 0mV to 1.2V, 66mV to 1.2V,  0mV to 2V, 400mV to 2V,0-5V, 1 to 5V, 0-15V, 3 to 15V, 0-24V, 4.8 to 24V into industrial standards (output current float on 16-20V DC) current 0 to 20mA, 4 to 20mA signals.... See below table "voltage to current industrial standard configuration models".

Note: Using industrial standard 249 Ohms 1% resistor on the meter side (deferential input preferred) will produce 0 to 5V for 0-20mA or 1 to 5V for 4 to 20mA. Using 499 Ohms 1% on the remote side will produce 0 to 10V and 2 to 10V.

Channel 1, 2, 3 & 4: UP to 4 Inputs Voltage (i.e. 2V-10V DC signal) - 4 Outputs Current (i.e. 4-20mA) with linear adjustment:

Channel 1, 2, 3 & 4: Up to 4 Inputs Voltage (i.e. 0-10V signal) - 4 Outputs Current (i.e. 0-20mA) with linear adjustment:

Quad In-Line Voltage to current (0-20mA or 4-20 mA) industrial standard configuration models:

Mounting Option

Simply mounted the board into your NEMA 4 box (enclosure) for watertight applications

CONVERTER-VMA420-4AXIL Features

• Built-in power LED indicator.

• 10V input 20mA output multi-turn trimmer adjustment.

• Power via 24V DC or AC industrial standard.

• Converts Quad 0-10VDC analog Voltages to 0-20mA or

• Converts Quad 2-10VDC analog Voltages to 4-20mA.

• Can be customized to accommodate your input voltage requirement.

• Industrial Standard output of 4-20mA makes the CONVERTER ideal for remote sensing applications.

• Linear current output.

• Current output rated up to 600mA.

• On board trimmer facilitates precise calibration of output current (10V input to 20mA output)

Specifications

• Input voltage                            0-10VDC

• Input Impedance                       >100K Ohms

• Output voltage                         Industrial standard 12-18VDC for driving long distance wires

• Output Current                         0 – 20mA standard, calibrated for 4-20mA with a 2 – 10VDC input signal

• PCB material                             FR4

• Input Filter                               L.P.F. 2Hz

• Max power consumption              0.5W

• Maximum load:                          Max load 600 Ohms

• Storage temperature                  40 - 70   [F]

• Operating temperature                32 - 140 [F] (0 to 60°C) @ 95% RH

• Low board DC voltage                 9 [V]

• Power source                            24VAC +/-12%, 50/60Hz, 0.6VA or 24VDC @ 45mA filtered

• Power indicator                         LED Red

• Adjustment                              Via trimmer for 20mA output @ 10VDC input or 10mA @ 5V

• Mounting                                 Four 0.125” (3.1mm) holes with centers distance of 2.9" * 2.450"

• Board dimensions                       3.2" * 2.75" (81.3mm * 69.8mm)

• Manufactured                           100% in USA

Pricing 

* Prices, SKU#, P# and colors are subject to change without notice. 

CONVERTER-VMA420-4AXIL Quad voltage (2V to 10V) to current (4mA to 20mA) converter with terminal-block (18 positions).

EID-CONVER-TER-QAXIL-VC420-6TB

$254.75

CONVERTER-VMA420-4AXIL Quad voltage (66.7mV to 1.2V) to current (4mA to 20mA) converter with terminal-block (18 positions).

EID-CONVER-TER-QAXIL-VC420-1-6TB

$273.33

CONVERTER-VMA420-4AXIL  Quad voltage (400mV to 2V) to current (4mA to 20mA) converter with terminal-block (18 positions).

EID-CONVER-TER-QAXIL-VC420-2-6TB

$273.93

CONVERTER-VMA420-4AXIL  Quad voltage (1V to 5V) to current (4mA to 20mA) converter with terminal-block (18 positions).

EID-CONVER-TER-QAXIL-VC420-5-6TB

$273.99

CONVERTER-VMA420-4AXIL  Quad voltage (3V to 15V) to current (4mA to 20mA) converter with terminal-block (18 positions).

EID-CONVER-TER-QAXIL-VC420-15-6TB

$273.99

CONVERTER-VMA420-4AXIL  Quad voltage (4.8V to 24V) to current (4mA to 20mA) converter with terminal-block (18 positions).

EID-CONVER-TER-QAxIL-VC420-24-6TB

$258.33

Remote load resistor 249 Ohms .25W, 1%

EID-R-025-249-1

$1.2

Remote load resistor 249 Ohms .50W, 1%

EID-R-050-249-1

$2.1

 ^•